In other words, the Repeater has to process one-way communication between your root Wireless router (or AP) and the terminal clients so the transmission time will be double-increased, while the speed will be decreased. Q2.Why does the wireless transmission rate speed down, while the wireless signal is stronger after repeated by the Repeater?Ī 1 : In compliance with the wireless transmission protocol, all the Repeater devices are set to work in half-duplex instead of full-duplex mode. What should I do if I cannot access the Repeater’s web management page?Ī 1: Make sure your computer is connected to the extended network.Ī2: Make sure your computer is set to obtain an IP address automatically.Ī3: If the Repeater has connected to the router, you should go to your router’s DHCP client list to obtain the Repeater’s current IP address. The upgrade process takes a few minutes to complete and the Repeater will automatically reboot itself when finished. You can backup all Setting of this router to a file, so you can make several copied of router configuration for security reason.Ĭlick “Manage-> Save/Reload setting ” located at the home page, the following message will be displayed on your web browserġ )Get from your service provider firmware file.Ģ)Click “Manage-> Upgrade Firmware” located at the home page.ģ)Make sure the firmware version is the same as the hardware version, then click “Browse” to select the firmware file.Ĥ)Click “Upgrade”. Factory Default and Settings Backup, Restore Click “Manage-> Password” located at the home page, the following message will be displayed on your web browser.Ģ. This is very important when you have wireless function enabled.ġ. Change Management passwordĭefault password of the Wifi Extender is ‘ad min”, and it’s displayed on the login prompt when accessed from web browser There’s a security risk if you don’t change the default password, since everyone can see it. and the Security Key is the same as your host Router’s WiFi key.If the connection is successful, The default Repeater ssid is set to be xxx ext(xxx indicates host Router’s 551.Press and hold the WPS Button on the side of the Wifi Repeater for one second within 2 minutes.Press the WPS Button on your host Router.Otherwise, please setup Using a Web Browser. Note: your host router should support WPS. You are recommended to use this method if your host router has a WPS button. WPS is an easier way to extend your host network. After the Repeater reboot has been completed, connect it to your router’s Ethernet port with an Ethernet cable. Change the SSID and Password, Click on “Apply” button, The Wifi Repeater will restart.ģ. Follow process 1 ~3.1,After logging in, you will see the web page below:Ģ.The Repeater Wifi-Repeater to the end of the host network’s 55ID and uses the same Wi-Fi password. Plug in the Repeater halfway between your router and the Wi-Fi dead zone. The Repeater can be used as a wireless adapter to connect any Ethernet enabled device, such as a Blu-ray player, game console, DVR, or smart TV, to your wireless network.Īfter the Repeater connected to the Internet, you can connect an Ethernet-only device to the Repeater using an Ethernet cable. After the reboot has been completed, the Wi-Fi Repeater is accessible under the SSID and the Wireless key. Click on “Apply” button, The Wi-Fi Repeater will restart. Note: The default Repeater ssid is set to be xxx ext(xxx indicates host Router’s SSID) and the Security Key is the same as your host Router’s WiFi key.Ĥ. Either keep the default SSID or customize it for extended network and insert the key of your network. After logging in, you will see the web page below:ģ. Enter ad min (all lowercase) for both Username and Password, then click Login.Ģ. Configure the Repeater Modeġ.Launch a web browser and type or in the address field. Connect your computer to the Repeater via an Ethernet cable. WiFi-Repeater).ĭisable the Wi-Fi on your computer. Click the Wi-Fi icon in the top right corner of the screen, and connect to the Repeater’s network (e.g. WiFi-Repeater).ĭisconnect the Ethernet (wired) connection from your computer (if any). Click the Wi-Fi icon on the taskbar and connect to the Repeater’s network (e.g. Disconnect your Ethernet (wired) connection from your computer.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |